Видео

Hey whats your max tow you have done?

is that the only way to take a lifter off

Why didn’t you demonstrate the nails in it? It can do 5 things and you showed 1. 🤷🏻‍♂️

You have to be a little careful with this device. These go back a long ways. You can end up tearing out the lip with this tool if too much force is used. Take and hold up on the lifter, tap it back down a little while still holding up on it, using your hand as a spring, if this makes any sense. You may have to do it for a little while but you won't tear the lifter up this way. It will come out after a while.

Just bought mine good deal

Can we use it to install baseboard in basement?

I have an 86 with a 5.0 tubular and the oil pan hits the rack with these mounts. Have to make spacers for the mounts for it to clear. (LS HOTROD PAN)

very cool video dude. Thanks A LOT ( not that I just locked myself out :/ ,,, 'cause i DIDN'T!! 0.O )!

That’s exactly what I need this tool for building my chicken coop putting the wire on it.

I plan to install a similar set of fog lights on my 1999 Crown Victoria. Hopefully, it won't be difficult.

How's it going with the 185? Getting much use of of it? any issues and what tung. you using for Aluminum? Cheers!

Watched the video, bought the tool. The thing will not catch onto the lifter whatsoever. What’s going on?

Very good detailed instructions. Especially for a chick like me. .

Where’d you get your intercooler kit from? Genius idea man

I can see this thing to work on a whole bunch of extracting jobs

Do you have any updates on this build? I’m thinking about doing the same thing seeing how well it works.

Great video bro, I wish I would’ve seen this video before I put mine in three weeks ago but u r on point for anyone else that’s having to put this in without a lift or taking the bumper off

How do you open it at first? Mine wont open itvfeels like im going to break the little door or something

😂😂 dont play with island mothers … she meant what she said and she will mash you up ! 🤣🤣

Hi Dustin, Another great video! I was wondering if you have a log or a note book? I noticed during your videos you've been shooting from the hip I'll say, about racing, the race car, parts, how it handled etc etc. When I raced, I would list everything from weather, track conditions & temp, (using a hot spot), every single change made no matter how small, including build up if any on the tires, blistering, air pressure, anything and everything from the time we started the weekend to when we were done. I believe i made a spread sheet (SS) and went right down the list. Our first year especially, every time the shop light came on, out came our log. Every thought, idea went in. Every single weekend for the next 16 months i believe, the SS was updated with tons of new items with at least 3 pages with just lines for unexpected add ons and😂 notes. I believe my time in the Marines helped me manage things better and thats where the SS idea came about. We also did this during our early drag racing years which helped a lot as you have stored data to fall back on. And thats what we did for ovals & road courses as well. Im sorry, i sorta went long and if you are doing this maybe i should of shortened this up a tad lol. Well, the main thing here is what you are doing for your children. And you are absolutely right, if you had dreams of doing anything in life, get it done while your young, because once you have a child, your focus does change. Especially if you are a caring, loving parent as you are. Sadly, not all parents are like this & i think thats a big problem we are currently having. What im trying to say is, all the work we do, the traveling, fixing and mending race cars and the hearts of our children, alls it takes is that one time you over hear your daughter saying to her friends as she points at you, "Thats my daddy!" And its all worth it. My children are all in their 30's now and I still over here it from time to time and even in my birthday cards. It truly makes your heart smile! Catching up on your videos, especially the mustang ones as i have an '02 like your sons & if you ever need anything, or someone to track something down for you I'm here for you. I love what you are doing. God bless brother, Gunny GySgt USMC Disabled Veteran

Stick to your guns brother. Don't give anything away. I was sitting here wanting to offer you $5k because i know its worth it. The parts are excellent as is your work and lets not forget labor! This country has gone sour and people have gotten lazy! Real lazy! Keep up the great work ethic and your videos. God bless, Gunny

Hey brother. Sorry to hear of the flood. We had a bad one here 2 years ago this past August. Floods basically ruin everything, especially your daily routine and everything else. My '02 is doing the same thing your son's is doing. I'm writing this at the start of your video. While you were sitting at the red light idling at 500! I'll watch and see what you come up with. I know I need a new fuel filter so that'll be the first thing I change. brb after video. Gunny GySgt USMC Disabled Veteran

How do I load nails in it?

Thank you!🎉 I bought the Dewalt Multi-Tacker years ago.... it lost it's packaging somewhere along the way, and I never used it till today... so, I've been trying to figure out why it wasn't stapling anything 🤔 I finally had to RUclips it 😂 but now I see there is an ELECTRIC ONE!!😮😲 Now I need this one! 😂🤣 Thanks for teaching me how to make this stapler work, and for teaching me about the New ELECTRIC STAPLER !😊 ❤ Because I "NEED" 🤭 the electric one in my life now! LOL😂❤🌻

Thanks for this video. I was looking for a tool for my crafts and wood projects. I did a search on this exact tool found your video. This is definitely what I need going to Home Depot tomorrow to grab it. Price is great and no getting in the way of the guys at our Gear shop. Oshawa Gear if you need anything for your builds my hubby loves your site. Thanks again your new follower

Hi thank you for the tutorial I just bought this stapler

I had a lifter that came out with a bent rod... so thanks for this... install with a magnet on a stick has been a bitch... this should make it easy!!

Where can I buy one? Lowes and Home Depot didn't have any electric 18 guage crown stapler.

I mightve missed it but what headers was used ? Or did you try and flip them ?

I mightve missed it but what headers was used ? Or did you try and flip them ?

The Y bit is for driving screw hooks.

I love your Duck Tales T shirt! :) oh and ya cool Di set tool.

You show how to half-ass stamp a letter in a pipe.

Bought one and it’s trash! Staples only go half way into osb. Has no kick back like you said. It’s cheaply made and jams every five staples. Junk.

What options are out there if you don't want a solid mount?

7/16 pair of pliers.....i think it's called a wrench

I think it's worth it. OEM makes some decent some decent stuff. I have some of their specialty tools

At last! You video finally answered my question (I've been looking for an hour). I got the HF aie hammer for $15.00, along with 1 chisel). I tightened the spring down all the way, but the chisel still moved about 1/2 an in. Since I am new to air tools,Ididn't know iif that was ok. I realiize the bit moves in and out, but didn't know if that was internal or not. I saw yours move that 1/2 in. None of the other videos or instructions mention that. Thank you

Would you happen to know if you can use this tool on a Ford 390 engine? Thanks for any advice.

does that downpipe not scrape on the ground at all??????

About to have to do this. I’m not looking forward to it😂

Dang, that's the wide one too. I thought it would come out wider on the rear. Not a lot of leverage there. How does it work and what are your 60's?

Hi Dustin, hope you're doing well. I was looking for some details on how to use a vise in English; I'm learning your native language, and my homework is to describe a process of grinding, cleaning, and cutting a rod using an angle grinder and one of these bench vises. I've learned a lot from your video! Thanks!

Dang… I gotta tow my enclosed up to wa state from Texas. Was thinking it’d be 13-15. Usually get about 18 at 75-80. Your computer showed 15.2 but you’re calc was 10.6?

Hell yeah I just got one and I’m using it to fix my couch the kids broke! I’m confident it will do the job.

OK so how did it turn out? I'm going to be doing mine this weekend

How bad is the ground clearence getting over speed bumps and such?

If u need a hand with your build I could help keep up the good work

It didn’t turn out flush when I put it on. The top and bottom stick out a little. Any ideas on why?

Wait is that a 5.3 that you using?